EN 840-3-2012 pdf download.Mobile waste and recycling containers – Part 3: Containers with 4 wheels with a capacity up to 1 300 I with dome lid(s), for trunnion and/or comb lifting devices – Dimensions and design.
3.1
mobile waste container
appropriately designed container fitted with wheels intended to temporarily stare waste
3.2
lifting device
structure which picks-up, tilts and empties containers
3.3
comb lifting device
lifting device in which the picking-up system consists of a row of teeth and a locking system to retain the container during emptying
3.4
trunnion lifting device
lifting device in which the picking-up system consists of a pair of arms with automatic locking mechanism to fit the trunnion to retain the container during emptying
3.5
volume
total space inside the container when the lid is closed
EN 840-3:2012 (E)
3.6
nominal volume
capacity
volume stated by the manufacturer
Note 1 to entry: See Table 1 without tolerances.
Note 2 to entry: The English term capacity and the French term capacite are translated in the German version by the term Nennvolumen
total permissible mass
mass of the container plus the nominal load
3.9
functional and safety dimensions
essential dimensions which ensure the functionahty and interchangeability of the container with the compatible lifting device and WhiCh are necessary for the operator’s safety and health
4 Volumes
This part of EN 840 identifies the two classes of containers:
Class I – small size (nominal volume up to 1 000 I):
Class II – large size (nominal volume between 1 000 I and 1 300 I).
Within the two above-mentioned classes of containers the following volumes are identified: 770 I, 1 000 I, 1100 I and 1 300 I. Nominal volumes different from those referenced can be used by agreement between user and manufacturer. The tolerance of the volumes shall be ± 5 % maximum measured according to
EN 840-5.
5 Dimensions and design
5.1 The design of the containers need not correspond to the drawings given in Figures 1 to 3. The functional dimensions given in Table 1 shall be respected. Recommendations for manufacturers of lifting devices are given in Annex A (see also EN 1501-1).
5.2 The container shall be constructed so that when it is unloaded or loaded with a nominal load (see Clause 6), it fits on an approved compatible lifting device. It shall be automatically locked safely into the lifting device during the lifting operation. If the container is equipped with a comb receiver, it shall correspond to Figure 4 and Figure 6.
5.3 The lid(s) shall cover the opening of the container completely. It shall be opened easily by the lifting device during the emptying cle Ittthey shall be made with at least two fixing points and have at least one means of opening.
5.4 Handles fitted in front of the trunnion shall have a measurement over the handles of 10 mm less than the actual measurement in Table 1 • dimension N 33. The handles and their location also shall be designed so that they do not damage the operator.
5.5 If the container has ribs in the frontal receiver they shall meet the requirements of Figure 4 and Figure 6.
5.6 The container shall have 4 swivel castors. Each swivel castor shall be capable of withstanding 113 of the total permissible mass. Each castor shall meet the requirements of EN 840-5. The container shall have facilities foe mounting the castor platine according to at least one of the measurements as shown in Figure 7.
5.7 All the surfaces of the container including design features shall be smooth and free of any foreign bodies or flaws.
5.8 The container should have a drain plug.
5.9 When direction locks are fitted they shall be fixed on at least two castors.
5.10 The container should be fitted with two beaked wheels to requirements of EN 840-5. In case of centralized braking and locking system the brake pedal and the lock shall be fixed on a lateral side of the container. The centralized locking shall be able to be unlocked with a standard triangular key as shown in Figure 8. The effectiveness of this centralized braking system shall conform to EN 840-5.
6 Nominal mass
The container shall be constructed strongly enough to carry a mass of 0,4 kg/dm3 x nominal volume.
Containers with a nominal volume of more than 1100 I shall be constructed strongly enough to carry a load of
440 kg.
7 Safety and health requirements
The container shall meet the safety and health requirements according to EN 840-6.
8 Testing
The container shall fulfil the performance requirements and the tests of EN 840-5.
9 Marking
9.1 Each container complying with the requirements of this part of EN 840 shall be durably and readably marked on the body in a visible part with:
— number of this European Standard (EN 840-3);
— nominal volume;EN 840-3-2012 pdf download.
EN 840-3-2012 pdf download
PS:Thank you for your support!
