EN 62090-2017 pdf download.Product package labels for electronic components using bar code and two- dimensional symbologies (IEC 62090:2017).
3.2
component package
commercial unit of components defined by the supplier including, if applicable, their means for protection, structured alignment or for automated assembly
Note I to entry Typical examples are shown in Figure 4.
Note 2 to entry For the purposes of this document, the term component psckage includes a multiple of the elements depicted in FIgure 4, e.g four reels in one box.
3.3
country of origin
manufacturing country where the product obtained its present identity as a part, subassembly, or finished product
Note 1 to entry: The definition of country of origin should be in line with local regulations.
4 Label data content and requirements
4.1 Data elements — general
This document allows mutual agreements between the supplier and the customer to alter or enhance any of the specifications done in this document.
The label format accommodates mandatory, optional and mutually agreed data elements. Examples of data element short titles are given in Annex D.
This document does not supersede or replace any applicable safety or regulatory marking or labelling requirements. This document is to be applied in addition to any other mandated labelling requirements. The labelling requirements of this document and other documents may be combined into one label or appear as separate labels.
Approval and conformity markings, branding elements and other information can be added when applicable. Typically, these are not relevant for automatic processing, and therefore not further outlined In this document.
The number included in the character count Is exclusive of overhead characters such as start and stop characters, data identifiers and any other characters required by a standard symbology specification for properly encoded data.
All data elements encoded in a machine-readable medium shall be preceded by the appropriate ISOI’IEC 15418 or ANSI MH1O.8.2 Data Identifier.
4.2 Mandatory data elements
4.2.1 Manufacturer Item identification — Dl “IP” and “25P”
The manufacturer-assigned item identification is mandatory.
If 1P is used, the conformity to the lSO/IEC 15459 series is achieved by its combination with the globally unique company ID “18V’.
4.2.2 Customer product code — Dl “P”
The customer product code is the code assigned to the product by the customer, and may be transmitted together with the order.
NOTE Customer product codes on component packages are relatively widely adopted. But when manufacturing on stock or selling via distributors, this information is not yet known.
Adding customer information on the label is subject to a purchase agreement between the supplier and the customer. If there is no specific purchase agreement, It is up to the manufacturer to add this information or not.
4.2.3 Manufacturer identification — Dl “18V” and “21V”
The manufacturer identification shall uniquely identify the manufacturer to which the component is traceable.
18\r Is the default manufacturer identification.
In case the manufacturer’s organizational sub unit is required, e.g. to indicate a manufacturing location, then DI “21V is used in addition to 18V. In case of mutual agreement between trading partners, 21V can be used instead of 18V”.
In human-readable form, the manufacturer identification is the full manufacturer name or its logo. In machine-readable form, the manufacturer identification is assigned by a recognized body that assigns company identification according to the ISOIIEC 15459 series.
The human-readable manufacturer identification and the machine-readable manufacturer identification are different. It is recommended that there be a 1:1 relation between human- readable and machine-readable manufacturer identification.
4.2.4 Quantity — DI “0” and “70”
The quantity shall be the quantity in the package or container to which the label is affixed. The default unit of measure for data identifier ‘Q is ‘EACH” or PIECES.
When a different unit of measure is required, as agreed between trading partners, data identifier ‘70 shall be used with the quantity followed by two alphanumeric characters representing the unit of measurement code defined In Annex 0 of ANSI MH1O.8.2.
It is recommended to use the quantity with a unit of measure only if the unit is different from piece.
Print only the significant digits for the human-readable quantity. Do not print leading zeros.
4.2.5 Traceability Identification — Dl “S” and “25S”, “IT” and “25T”
4.2.5.1 General
The traceability identification shall be assigned by the manufacturer. This category of identification includes serial numbers and lot/batch numbers.
Traceability identification should be either a serial number (using data identifier S or 25S”) or a lot/batch number (using data identifier 1T or 25T).
In certain circumstances, both the serial number and the lot/batch number may be shown on the label. In this case, at least one of the two shall be encoded in a linear bar code and both shall be included in the 2D symbol.
4.2.5.2 Serial number — Dl “5” and “25S”
A serial number is a unique code assigned by the supplier to an entity for its lifetime. The format for the serial number is to be defined by the manufacturer.
4.2.5.3 Lotlbatch number — Dl “IT” and “25T”
A lot/batch number is a code assigned by the supplier to identify or trace a unique group of entities (e.g. manufacturing lot, batch, inspection lot). The format for the lot/batch number is to be defined by the manufacturer.
4.2.6 Country of origin — Dl “4L’
The country of origin shall be shown in human-readable information using the full country name.
This shall be in addition to the two-character country codes as per ISO 3166 data being encoded in a machine-readable symbol.
4.2.7 Production date — Dl “16D”.EN 62090-2017 pdf download.
EN 62090-2017 pdf download
PS:Thank you for your support!
