EN 2569-1991 pdf download.Aerospace series – Control cable fittings and turnbarrels Technical specification.
This EN 2569 siwcifies the required characteristics, the qualification and acceptance inspections and tests for:
— end fittings swaged onto control cables:
— cable turnharrel components:
— cable turnbarrel assemblies.
2 References
ISO 2020, Aerospace — Mechanical system parts — Preformed flexible steel wire rope for aircraft controls — Technical specification.
ISO 2859. Sampling procedures and tables for inspection by attributes.
ISO 5855.1, Aerospace constructions — MJ threads — Part 1: General requirements.
ISO 5855.2, Aerospace constructions — M.J threads — Part 2: Limit dimensions bolts and nuts.
EN 2000. Aerospace series — Quality assurance — EN aerospace prod ucts — Approval of the quality system of ma ufacturers1 1•
EN 2348. Aerospace series — Control cable assemblies — Technical specification.
EN 2353, Aerospace series — Turnbarrels, control cable in corrosion resisting steel— Dimensions and loads. EN 2354. Aerospace series — Eye-ends, threaded, control cable in corrosion resisting steel — Dimensions and loads.
EN 2355. Aerospace series — Fork-ends, threaded, control cable in corrosion resisting steel — Dimensions and loads.
EN 2356. Aerospace series — Fork-ends, threaded, control cable for rolling bearings in corrosion resisting steel — Dimensions and loads.
EN 2357. Aerospace series — Stud-ends in corrosion resisting steel swaged on type, control cable — Dimensions and loads.
EN 2358. Aerospace series — Eye-ends in corrosion resisting steel swaged on type, control cable — Dimensions and loads.
EN 2359. Aerospace series — Fork-ends in corrosion resisting steel swaged on type. control cable — Dimensions and loads.
EN 2360. Aerospace series — Fork.ends for rolling hearings in corrosion resisting steel swuged on type, control cable — Dimensions and loads.
EN 2361. Aerospace series — Ball-ends, double shank in corrosion resisting steel swaged on type, control
cable — Dimensions and loads.
EN 2362. Aerospace series — Ball-ends, in corrosion resisting steel swcjged on type, control cable — Dimensions and loads.
EN 2363. Aerospace series — Locking clips for turnhuckles of control cables – Di,nensions.
EN 2516. Aerospace series — Passivat ion of corrosion resistant steels2.
EN 2609. Aerospace series — Turnbarrels, control cable in copper-zinc alloy — Dimensions and loads.
3 Definitions
3.1
end fittings for swaging onto control cables
defined by standards EN 2357. EN 2358. EN 2359, EN 2360. EN 2361 and EN 2362
3.2
cable turnbarrel components
defined by standards EN 2353. EN 2354. EN 2355. EN 2356. EN 2363 and EN 2609
3.3
cable turnbarrel assembly
deflned as the assembly of the following components:
— turnbarrel:
— locking dip;
— threaded junction parts (2) which can be fork.ends. eye.ends or stud.ends swaged on type. these various assemblies arc not the subject of product standards
3.4
surface discontinuities
crack
rupture in the material which may extend in all directions and which may be intercrystalline or transcryscalline in character
score
open surface defect which is the result from a metallic tearing lap
surface defect caused by folding over metal particles or sharp edges which are then rolled or forged into the surface
seam
unwelded lap which appears as an open defect in the material
3.5
production batch
a production batch comprises parts having the same identity block, manufactured in the same production sequence, produced from the same material hatch and having undergone together the heat treatments
3.6
delivery hat(h
two cases may arise:
Homogeneous batch made up of one and the same production batch:
The sampling plan is applicable to the whole of the delivery batch.
— Heterogenous batch made up of different production batches:
The sampling plan is applicable to each production hatch.
4 Required characteristics, inspection and test methods
See Table 1.
5 Quality assurance
5.1 Manufacturer approval
See EN 2000.
5.2 Qualification
5.2.1 End-fittings or turnbarrel components
According to Table 5 and Table 6.
The order of the inspections or tests is left to the initiative of the qualification authority.
5.2.2 Turnbarrel assembly
Even though they are not the subject of product standards, the turnbarrel assemblies shall be submitted to the tests given in Table 7 and Table 8 in order to qualify their individual components on the basis of their behaviour in service.
The order of the inspection or tests is left to the initiative of the qualification authority.EN 2569-1991 pdf download.

Share on Facebook

Post on X

Follow us

Save