EN 198-2008 pdf download

07-13-2021 comment

EN 198-2008 pdf download.Sanitary appliances – Baths made from crosslinked cast acrylic sheets – Requirements and test methods.
This EN 198 specifies requirements for baths for domestic purposes made from crosslinked cast acrylic sheet conforming to EN 263 with the aim of ensuring that the product, when installed in accordance with the manufacturer’s instructions, will provide satisfactory performance in use.
This European Standard is applicable to all sizes and shapes of baths.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
EN 232. Baths — Connecting dimensions
EN 263, Sanitary appliances — Crossiinked cast acrylic sheets for baths and shower trays for domestic
purposes
3 Terms and definitions
For the purposes of this document the following terms and definitions apply.
3.1
domestic purposes
use in homes, hotels, accommodation for students, hospitals and similar buildings, except when special medical provisions are required
4 Requirements
4.1 General
The manufacturer shall provide instructions for installation and care with each bath.
The bath shall be free from sharp edges that would be exposed after the installation of the bath in accordance with the manufacturers instructions.
4.2 Material
The bath shall be manufactured from crosslinked cast acrylic material in accordance with EN 263.
4.3 Surface appearance
When the bath is visually inspected under strong and oblique illumination there shall be no evidence of cracks, chips, or other surface defects, such as unexpected changes in colours, etc., which will impair the appearance or performance of the bath.
4.4 Waste outlet hole
The bath shall have at least one outlet hole. The dimensions of the waste outlet hole and the clearance around the waste outlet hole shall either be in accordance with the requirements of EN 232 or the manufacturer shall supply or recommend a suitable waste outlet fitting.
EN 198:2008 (E)
4.5 Overflow hole
When the bath is provided with an overflow hole the dimensions of the overflow hole and the clearance around the overflow hde shall either be in accordance with the requirements of EN 232 or the manufacturer shall supply or recommend a suitable overflow fitting.
4.6 Hole edges
The edges of any holes in the bath shall not show evidence of chips, cracks, or any other defects that may
impair the appearance or performance of the bath.
4.7 Bath-mounted tapware
When the bath is intended to accommodate bath-mounted tapware the space and area provided shall either comply with the requirements of EN 232 or the manufacturer shall supply or recommend suitable tapware.
4.8 Handgrips
When a handgrip(s) is fitted it shall be tested in accordance with Annex A and the bath and the handgrip shall be free from any permanent deformation or other defects that will impair the functioning and/or the appearance of the bath.
If not pre-fitted by the manufacturer, the manufacturer’s Instructions shall indicate how and where the handgrips are fitted.
4.9 Dimensional deviations
The dimensions of baths shall not deviate from the size quoted by the manufacturer by more than ± 5 mm.
If the manufacturer states two sizes (e.g. both a work size and a nominal size), the manufacturer shall state to which size the permitted deviations apply.
For round baths, length and width correspond to the diameter.
4.10 Geometric deviations
4.10.1 General
The straight sides or edges of the bath that might abut independent surroundings or supporting structures shall comply with the requirements of 4.10.2 to 4.10.4 and all baths shall comply with 4.10.5. These requirements are not applicable to sides or edges that are purposely designed as curves or slopes.
4.10.2 Squaring
When tested in accordance with A.2.2, the deviation from square, Aq, shall be less than or equal to 5 mm.
4.10.3 Straightness of the rim sides
When tested in accordance with A.2.3, the deviation from straightness of the rim sides, As. shall be less than
or equal to 5 mm.
4.10.4 Straightness of the bottom edge of the rim
When tested in accordance with A.2.4, the total deviation from straightness of the bottom edge of the rim. Ar, shall be less than or equal to 5 mm.EN 198-2008 pdf download.

                                           Related Information                                             Download
PS:Thank you for your support!
EN 152-1:1988 pdf download EN Standards

EN 152-1:1988 pdf download

EN 152-1:1988 pdf download,Test methods for wood preservatives;Laboratory method for determining the preventive effectivenessof a preservative treatment against blue stain in service Part 1:Brushing procedure. The test method described in this European Standard is a laboratory method...
Read More
EN 74:1988 pdf download EN Standards

EN 74:1988 pdf download

EN 74:1988 pdf download.Cooplers,loose spigots and base-plates for use in working scaffolds and falsework made of steel tubes; Requirements and test procedures Key words Steel tubes,Scaffolding,Fasteners,Pipe fittings,Centring pins,Supports,Equipment specifications,Inspection methods,Sampling,Mechanical tests.
Read More
EN 50061:1988 pdf download EN Standards

EN 50061:1988 pdf download

EN 50061:1988 pdf download,Safety of implantable cardiac pacemakers. This standard EN 50061:1988 specifies safety and other requirementsexclusively for all types of wholly implantable cardiac PACEMAKERS. This standard EN 50061:1988 also establishes basic terminology and definitions and includes...
Read More

LEAVE A REPLY

Anonymous netizen Fill in information