EN 1329-1-2014 pdf download.Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Unpiasticized poly(vinyl chloride) (PVC-U) – Part 1: Specifications for pipes,
fittings and the system.
This part of EN 1329 is also applicable to PVC-U pipes, fittings and the system intended for the following
purposes:
— ventilating part of the pipework in association with discharge applications;
— rainwater pipework within the building structure.
It also specifies the test parameters for the test method referred to in this European Standard.
This European Standard covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours.
NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
For external above ground application additional requirements depending on the climate should be agreed between the manufacturer and the user.
NOTE 4 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conformrig to this European Standard, provided they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 24
NOTE 5 Joints and adhesives are considered to be part of the system as covered in the scope.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
EN 681-1, Elastomeric seals – Materials requirements far pipe joint seals used in water and drainage applications – Part 1: Vulcanized rubber
EN 681-2, Elastomeric Seals – Materials requirements for pipe joint seals used in water and drainage applications – Part 2: Thermoplastic elastamers
EN 1401-1:2009, Plastics piping systems for non-pressure underground drainage and sewerage – Unplasticized poly(vinyl chloride) (PVC-U) – Part 1: Specifications for pipes, fittings and the system
EN 1905. Plastics piping systems – Unpiasticized poly(vinyl chloride) (PVC-U) pipes, fittings and material – Method for assessment of the PVC content based on total chlorine content
EN 10204:2004, Metallic products – Types of inspection documents
EN 14680, Adhesives for non-pressure thermoplastic piping systems – Specifications
EN 14814, Adhesives for thermoplastic piping systems for fluids under pressure – Specifications
EN ISO 472. Plastics – Vocabulary (ISO 472)
EN ISO 580, Plastics piping and ducting systems – lnjection-moulded thermoplastics fittings – Methods for visually assessing the effects of heating (ISO 580)
EN ISO 1043-1, Plastics – Symbols and abbreviated terms – Part 1: Basic polymers and their special characteristics (ISO 1043-1)
EN ISO 1167-1, Thermciplastics pipes, fittings and assemblies for the conveyance of fluids – Determination of the resistance to internal pressure – Part 1: General method (ISO 1167-1)
EN ISO 1167-2, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids – Determination of the resistance to internal pressure – Part 2: Preparation of pipe test pieces (ISO 1167-2)
EN ISO 1183-1, Plastics – Methods for determining the density of non-cellular plastics – Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1)
EN ISO 2505, Thermoplastics pipes – Longitudinal reversion – Test method and parameters (ISO 2505) EN ISO 3126, Plastics piping systems – Plastics components – Determination of dimensions (ISO 3126)
EN ISO 6259-1, Thermoplastics pipes – Determination of tensile properties – Part 1: General test method (ISO 6259-1)
EN ISO 13229, Thermoplastics piping systems for non-pressure applications – Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings – Determination of the viscosity number and K-value (ISO 13229)
ISO 2507-1, Thermoplastics pipes and fittings – Vicat softening temperature – Part 1: General test method ISO 3127, Thermoplastics pipes – Determination of resistance to externaiblows – Round-the-clack method
ISO 6259-2. Thermoplastics pipes – Determination of tensile properties – Part 2: Pipes made of unpiasticized
poly(vinyl chloride) (PVC-u), chlorinated poly (vinyl chloride) (PVC-C) and high-impact poly (vinyl chloride)
(PVC-HI)
ISO 9852, Unplasticized poly(vinyl chloride) (PVC-U) pipes – Oichloromethane resistance at specified temperature (DCMT) – Test method.EN 1329-1-2014 pdf download.

Share on Facebook

Post on X

Follow us

Save