EN 1313-1-2010 pdf download

07-12-2021 comment

EN 1313-1-2010 pdf download.Round and sawn timber – Permitted deviations and preferred sizes – Part 1: Softwood sawn timber.
This EN 1313-1 specifies permitted deviations for thickness and width at reference moisture content and adjustments for changes in size due to changes in moisture content. Preferred sizes for thicknesses of 38 mm and over are also specified.
This standard applies to softwood sawn timber.
An informative annex gives complementary national sizes.
NOTE A.5 includes for France the concept of preferred size for green timber,
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
EN 844-1:1995, Round and sawn timber — Terminology — Part 1: General terms common to round timber and sawn timber,
EN 844-3:1995, Round and sawn timber — Terminology — Part 3: General terms relating to sanw timber EN 844-4:1997, Round and sawn timber — Terminology — Part 4: Terms relating to moisture content
EN 844-6:1997, Round and sawn timber — Terminology — Part 6: Terms relating to dimensions of sawn timber
EN 1309-1 • Round and sawn timber — Method of measurement of dimensions — Part 1: Sewn timber
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 844-1:1995. EN 844-3:1995, EN 844-4:1997 and EN 844-6:1997 apply.
4 Reference moisture content
The reference moisture content is 20 %. The target sizes in Clause 7 are applied at this moisture content,
5 Change in size due to changes In moisture content
Unless there is evidence to the contrary, it shall be assumed that the thickness and width of a piece of timber Will increase by 0,25 % every 1 % of moisture content higher than 20 % up to fibre saturation point, and decrease by up to 0,25 % every 1 % of moisture content lower than 20 %. The above values are independent of the species
6 Permitted deviations
The average thickness and the average width shall not be less than the target sizes.
Permitted deviations of cross-sectional sizes at 20 % moisture content are as follows:
— For thickness and width < 100 mm: + 3 mml – 1 mm; Forthicknessandwidth> 100mm: +4 mml-2mm
For length: no minus tolerance, plus tolerance agreed by contract.
7 Common traditional target cross-sectional sizes
Sizes shall be measured according to EN 1309-1.
Common traditional target cross-sectional sizes of softwood sawn timber with thickness of 38 mm and over either based on imperial measure, see Table 1; or
based on metric measure, see Table 2.EN 1313-1-2010 pdf download.

                                           Related Information                                             Download
PS:Thank you for your support!
EN 152-1:1988 pdf download EN Standards

EN 152-1:1988 pdf download

EN 152-1:1988 pdf download,Test methods for wood preservatives;Laboratory method for determining the preventive effectivenessof a preservative treatment against blue stain in service Part 1:Brushing procedure. The test method described in this European Standard is a laboratory method...
Read More
EN 74:1988 pdf download EN Standards

EN 74:1988 pdf download

EN 74:1988 pdf download.Cooplers,loose spigots and base-plates for use in working scaffolds and falsework made of steel tubes; Requirements and test procedures Key words Steel tubes,Scaffolding,Fasteners,Pipe fittings,Centring pins,Supports,Equipment specifications,Inspection methods,Sampling,Mechanical tests.
Read More
EN 50061:1988 pdf download EN Standards

EN 50061:1988 pdf download

EN 50061:1988 pdf download,Safety of implantable cardiac pacemakers. This standard EN 50061:1988 specifies safety and other requirementsexclusively for all types of wholly implantable cardiac PACEMAKERS. This standard EN 50061:1988 also establishes basic terminology and definitions and includes...
Read More

LEAVE A REPLY

Anonymous netizen Fill in information