BS/EN 62343-3-1-2016 pdf download

07-30-2021 comment

BS/EN 62343-3-1-2016 pdf download.Dynamic modules Part 3-1 : Performance specification templates-Dynamic channel equalizers.
Additional specification parameters may be included for product specifications or performance specifications. However, specification parameters specified in this standard should not be removed from the product specifications or performance specifications.
Technical information regarding dynamic channel equalizers and their applications in DWDM systems is described in IEC TR 62343-6-1.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
IEC 61300-2-14, Fibre optic interconnecting devices and passive components — Basic test and measurement procedures — Part 2-14: Tests — High optical power
IEC 61300-3-2, Fibre optic interconnecting devices and passive components — Basic test and measurement procedures — Part 3-2: Examinations and measurements — Polarization dependent loss in a single-mode fibre optic device
IEC 61300-3-6, Fibre optic interconnecting devices and passive components — Basic test and measurement procedures — Part 3-6: Examinations and measurements — Return loss
IEC 6 1300-3-29, Fibre optic interconnecting devices and passive components — Basic test and measurement procedures — Part 3-29: Examinations and measurements — Spectral transfer characteristics of DWDM devices
IEC 61300-3-32, Fibre optic interconnecting devices and passive components — Basic test and measurement procedures — Part 3-32: Examinations and measurements — Polarization mode dispersion measurement for passive optical components
IEC 61300-3-38, Fibre optic interconnecting devices and passive components — Basic test and measurement procedures — Part 3-38: Examinations and measurements — Group delay, chromatic dispersion and phase ripple
IEC 61753-021-2, Fibre optic interconnecting devices and passive components performance standard — Part 02 1-2: Grade C/3 single-mode fibre optic connectors for category C — Controlled environment
IEC 62343. Dynamic modules — General and guidance
3 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 62343 apply.
4 Test report
Fully documented test reports and supporting evidence shall be prepared and be available for inspections as evidence that the tests have been carried out and complied with.
5 Reference components
The testing for DCE components does not require the use of reference components.
6 Performance requirements
6.1 Dimensions
Dimensions shall comply with either an appropriate IEC interface standard, or with those given in the manufacturers drawings, where the IEC interface standard does not exist or cannot be used.
6.2 Sample size
The test sample size and sequencing requirements for the module components shall be defined in the relevant specification.
6.3 Test details and requirements
The requirements are given only for non-connectorized DCE devices. For connectorized components, the connector performances shall be in compliance with IEC 61753-021-2.
A minimum length of fibre or cable of 1,5 m per port shall be included in all climatic and environmental tests.
The channel spacings, unless otherwise specified, shall be in accordance with ITU-T Recommendation G.694,1. Environmental tests shall be measured for a single input/output port combination.
The test details and requirements are given in Table 1.BS/EN 62343-3-1-2016 pdf download.

                                           Related Information                                             Download
PS:Thank you for your support!
BS EN 12607-3-2000 pdf download BS Standards

BS EN 12607-3-2000 pdf download

BS EN 12607-3-2000 pdf download.Methods of test for petroleum and its products — BS 2000-460.3: Bitumen and bituminous binders — Determination of the resistance to hardening under the influence of heat and air — Part 3: RFT...
Read More
EN 12329-2000 pdf download BS Standards

EN 12329-2000 pdf download

BS EN 12329-2000 pdf download.Corrosion protection of metals — Electrodeposited coatings of zinc with supplementary treatment on iron or steel. This BS EN 12329 specifies requirements for electrodeposited coatings of zinc on iron or steel witt supplementary...
Read More
BS EN 1430-2000 pdf download BS Standards

BS EN 1430-2000 pdf download

BS EN 1430-2000 pdf download.Methods of test for petroleum and its products — BS 2000-292:Bitumen and bituminous binders — Determination of particle polarity of bitumen emulsions (Identical with IP 292-2000). This BS EN 1430 specifies a method...
Read More

LEAVE A REPLY

Anonymous netizen Fill in information