BS/EN 6098-2019 pdf download.Aerospace series – Rod-end with bearing per EN 6097 in corrosion resisting steel, extra wide inner ring, external threaded shank- Dimensions and loads – Inch series.
This BS/EN 6098 specifies the characteristics of adjustable rod ends consisting of:
— a spherical plain bearing, metal to metal, in corrosion resisting steel, extra wide series (EN 6097);
— a rod—end with threaded shank with an optional longitudinal groove for locking purposes.
They are intended for use in fixed or moving parts of the aircraft structure and their control
mechanisms.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
EN 21 33. Aerospace series — Cadmium plating of steels with specified tensile strength ≤ 1 450 MPa, copper, copper alloys and nickel alloys
EN 2424. Aerospace series — Marking of aerospace products
EN 6097, Aerospace series — Bearing, spherical plain, metal to metal, extra wide inner ring in corrosion
resisting steel — Dimensions and loads — Inch series
EN 6099, Rod-ends with plain bearing, metal to metal — Technical Specification1
ISO 1132-1. Rolling bearings — Tolerances — Part 1: Terms and definitions
ISO 3161. Aerospace — UN) threads — General requirements and limit dimensions
ISO 3353-1, Aerospace — Lead and runout threads — Part I: Rolled external threads
ISO 3353-2, Aerospace — Lead and runout threads — Part 2: Internal threads
ISO 8074, Aerospace — Surface treatment of austenitic stainless steel parts
MI L- PRF- 23827, Grease, aircraft and instrument, gear and actuator screw, NA TO code No.G-354 metric2
MIL-PRF-46010, Lubricant, solid film, heat cured, corrosion — inhibiting, NATO Code-S-I 7382
MIL-PRF-8 1322, Grease, aircraft, general purpose, wide temperature range, NATO Code G-3952
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at http://www.iso.org/obp
— IEC Electropedia: available at http://www.electropedia.org/
Symbols of limit deviations are in accordance with definitions of ISO 1132-1.
a’ maximum angle of tilt of the outer ring with respect to the inner ring, the spherical surface of the outer ring being completely in contact with the inner ring
C5 permissible static radial load
C, pushoutloads
single plane mean bore diameter deviation
deviation of a single bore diameter
fatigue load
4 Requirements
4.1 Configuration, dimensions, tolerances and mass
Configuration, dimensions, tolerances and mass shall be according to Figure 1 and Table I and Table 2.
Table 1: Dimensions and tolerances are expressed in millimetres (inches).
Figure 1: Dimensions and tolerances for Ra max. are expressed in pim (pun).
Values apply alter surface treatment.
4.2 Surface roughness
Surface roughness shall be according with Figure 1.
Surface roughness is measured before surface treatment.
4.5 Materials
Inner ring: See product standard EN 6097.
Outer ring: See product standard EN 6097.
Rod-end body: See AMS 5643, hardness 35 ≤ HRC S 42.
4.6 Surface treatment
Rod-end body:
— code T: passivated according t ISO 8074;
— code P: cadmium plating and chromating according to EN 2133, 10 urn to 20 pm (400 pin to 800 I.Lin);
— exception: threads, 5 pm to 15 pm (200 pin to 600 pin);
— bearing: see EN 6097, code T.
4.9 Temperature range and lubricant
They shall be used in the temperature range as determined by the grease capability see below.
As they are lubricated by means of the following greases:
— code A: grease as per MIL-PRF-23827 type 1, operating temperature range —73 °C to 121 °C;
— code B: grease as per MIL-PRF-81322. operating temperature range —54°C to 177 °C.
In both cases the spherical surface of the outer or inner ring, have to be provided with a dry-film lubricant as per MIL•PRF-46010 or equivalent (anti-seizing protection).
6 Marking
Marking shall be according EN 2424, style A.
7 Technical specification
Technical specification shall be according to EN 6099.
8 Quality management system
The manufacturer’s operations shall be an approved production organisation for aerospace products and shall demonstrate that it has implemented and is able to maintain a quality management system (e.g. according to EN 9100 or an equivalent aerospace accepted and established quality management system).
The qualification procedure for aerospace standard products (e.g. according to EN 9133 or an equivalent aerospace accepted and established qualification procedure) shall be used and documented according to the specified tests if not otherwise agreed between customer and supplier.BS/EN 6098-2019 pdf download.
BS/EN 6098-2019 pdf download
PS:Thank you for your support!
