BS/EN 6098-2019 pdf download.Aerospace series – Rod-end with bearing per EN 6097 in corrosion resisting steel, extra wide inner ring, external threaded shank- Dimensions and loads – Inch series.
This BS/EN 6098 specifies the characteristics of adjustable rod ends consisting of:
— a spherical plain bearing, metal to metal, in corrosion resisting steel, extra wide series (EN 6097);
— a rod-end with threaded shank with an optional longitudinal groove for locking purposes.
They are intended for use in fixed or moving parts of the aircraft structure and their control
mechanisms.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this documeni For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
EN 2133, Aerospace series — Cadmium plating of steels with specified tensile strength .≤1 450 MPa, copper, copper alloys and nickel alloys
EN 2424, Aerospace series — Marking of aerospace products
EN 6097. Aerospace series — Bearing, spherical plain, metal to metal, extra wide inner ring in corrosion
resisting steel — Dimensions and loads — inch series
EN 6099. Rod-ends with plain bearing, metal to metal — Technical Specification’
ISO 1132-1, Rolling bearings — Tolerances — Part 1: Terms and definitions
ISO 3161, Aerospace — UN] threads — General requirements and limit dimensions
ISO 3353-1, Aerospace — Lead and runout threads — Part 1: Rolled external threads
ISO 3353-2, Aerospace — Lead and runout threads — Part 2: Internal threads
ISO 8074, Aerospace — Surface treatment of austenitic stainless steel parts
Ml L- PRF-23827, Grease, aircraft and instrument, gear and actuator screw, NA TO code No.G -354 metric2
MIL-PRF-46010, Lubricant, solid film, heat cured, corrosion — inhibiting, NATO Code-S-i 7382
Ml L- PRF-8 1322. Grease, aircraft, general purpose, wide temperature range, NA TO Code G-3952
SAE AMS 5643, Steel, corrosion resistant, bars, wire, forgings. tubing and rings l6Cr-4.ONi-O.3OCb-4.OCu, Solution and Precipitation Heat Treated (H1025)
TR 4475, Bearings and mechanical transmissions for airframe applications — Vocabulamy4
3 Terms, definitions and symbols
For the purposes of this document, the terms and definitions given in TR 4475 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
ISO Online browsing platform: available at http://www.iso.org/obp
— IEC Electropedia: available at http://www.electropedia.org/
Symbols of limit deviations are in accordance with definitions of ISO 1132-1.
a’ maximum angle of tilt of the outer ring with respect to the inner ring, the spherical surface of the outer ring being completely in contact with the inner ring
C5 permissible static radial load
C, push out loads
4dmp single plane mean bore diameter deviation
4 deviation of a single bore diameter
C1 fatigue load
4 Requirements
4.1 Configuration, dimensions, tolerances and mass
Configuration, dimensions, tolerances and mass shall be according to Figure 1 and Table 1 and Table 2.
Table 1: Dimensions and tolerances are expressed in millimetres (inches).
Figure 1: Dimensions and tolerances for Ra max. are expressed in pm (itin).
4.5 Materials
Inner ring: See product standard EN 6097.
Outer ring: See product standard EN 6097.
Rod-end body: See AMS 5643, hardness 35 ≤ HRC ≤ 42.
4.6 Surface treatment
Rod-end body:
code T: passivated according to ISO 8074;
— code P: cadmium plating and chromating according to EN 2133. 10 pm to 20 tm (400 iin to 800 pin);
— exception: threads. S pm to 15 pm (200 pin to 600 pin);
— bearing: see EN 6097. code T.
4.9 Temperature range and lubricant
They shall be used in the temperature range as determined by the grease capability see below.
As they are lubricated by means of the following greases:
— code A: grease as per MIL-PRF-23827 type 1, operating temperature range —73 °C to 121 °C; code B: grease as per MIL-PRF-81322. operating temperature range —54°C to 177 °C.
In both cases the spherical surface of the outer or inner ring, have to be provided with a dry-film lubricant as per MIL-PRF-46010 or equivalent (anti-seizing protection).BS/EN 6098-2019 pdf download.
BS/EN 6098-2019 pdf download
PS:Thank you for your support!
