BS/EN 60384-14-2-2016 pdf download.Fixed capacitors for use in electronic equipment Part 14-2: Blank detail specification — Fixed capacitors for electromagnetic interference suppression and connection to the supply mains — Safety tests only.
I General data
1.1 Recommended method(s) of mounting (to be inserted)
See IEC 60384-14:2013, 1.4.2.
1.2 Dimensions
The dimensions expressed as maximum dimensions or as nominal dimensions with a tolerance shall be given in the manufacturer’s specification.
1.3 Ratings and characteristics
Ratings and characteristics are as listed below:
a) Capacitance range
b) Tolerance on nominal capacitance
C) Rated voltage
d) Rated current (if applicable)
e) Climatic category
1) Rated temperature
g) Tangent of loss angle
h) Insulation resistance
I) Category of passive flammability
Values of capacitance related to the rated voltage, dimensions and ordering code/type designation shall be given in the manufacturers specification.
1.4 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (Including any amendments) applies.
IEC 60384-1:2016. Fixed capacitors for use in electronic equipment — Part 1: Generic specification
IEC 60384-14:2013, Fixed capacitors (or use in electronic equipment — Part 14: Sectional specification — Fixed capacitors for electromagnetic interference suppression and connection to the supply mains
IEC 61193-2:2007. Quality assessment systems — Part 2: Selection and use of sampling plans for inspection of electronic components and packages
1.5 Marking
The marking of the capacitor, if any, and the packaging shall be in accordance with
IEC 60384-14:2013. 1.6.
The details of the marking of the component and packaging shall be given in full in the detail specification.
1.6 Ordering information
Orders for capacitors covered by this specification shall contain, in clear or in coded form, the following information:
a) nominal capacitance;
b) tolerance on nominal capacitance;
c) rated voltage;
d) manufacturer’s type designation;
e) number and issue reference of the detail specification and style reference.
1.7 AddItional information (not required for Inspection purposes)
1.8 Additional or increased seventies or requirements to those specified in the generic and!or sectional specification
Additional or increased requirements should be specified only when essential. They should be given in Table 1.
Note that this declaration is confidential to the manufacturer and the certification body.
The purpose of this description is to register essential data and the basic design of the capacitors for which approval is sought. The completed form shall be submitted to the relevant Certification Body prior to any approval testing Its circulation to the other parties is left to the decision of the manufacturer.
Changes to the declared design are permitted only after notifying the Certification Body in writing. In this case, the Certifying Body will decide on necessary steps to be taken. As a maximum a complete requalification may be required.
Registration number:
(to be allocated by the Certifying Body)
I Applicant:
2 Manufacturer:
3 Manufacturing site:
4 Type designation:
5 Classlsubclass:
6 CIrcuit diagram:
7 DielectrIc
7.1 Material,
7.2 Thickness,
7.3 Density (paper only),
7.4 Number of individual layers.
8 Electrode(s)
8.1 Material,
8.2 Kind of generation (e.g. foil, evaporated on to film or paper).
9 Capacitor element, arrangement of the Individual layers:
10 Impregnant: (If applicable)
11 Encapsulation
11 .1 Material(s) for cases, resins, etc. (as applicable),
11 .2 Material of outer insulation (if applicable).
12 Outline dimensions.BS/EN 60384-14-2-2016 pdf download.
BS/EN 60384-14-2-2016 pdf download
PS:Thank you for your support!
