BS EN 41003-2009 pdf download.Particular safety requirements for equipment to be connected to telecommunication networks and/or a cable distribution system.
This BS EN 41003 applies to equipment designed and intended to be connected as a terminal to a TELECOMMUMCATION NETWORK and/or a CABLE DISTRIBUTION SYSTEM termination. It does not apply to equipment covered by EN 60950-1 and EN 60065.
This European Standard specifies the safety requirements of the interface to the TELECOMMUNICATION NETWORK and/or the CABLE DISTRIBUTION SYSTEM only and it does not specify any other safety requirements.
It applies regardless of ownership or responsibility for installation or maintenance of the equipment, and regardless of the source of power.
This European Standard, in accordance with the ‘principles of safety’ given in the introduction of EN 60950-1, covers the requirements and compliance criteria under three headings.
• Protection of equipment USERS from hazards in the equipment. The USER is considered to be protected from hazards in the equipment if the equipment complies with a relevant safety standard, for example one of those listed in Annex A, but compliance with those standards is not part of this European Standard.
• Protection of SERVICE PERSONNEL working on a TELECOMMUNICATION NETWORK and/or a CABLE
DISTRIBUTION SYSTEM and other USERS of a TELECOMMUNICATION NETWORK and/or a CABLE
DISTRIBUTION SYSTEM, from hazardous conditions on a TELECOMMUNICATION NETWORK and/or a
CABLE DISTRIBUTION SYSTEM resulting from the connection of the equipment.
• Protection of equipment USERS from voltages on a TELECOMMUNICATION NETWORK and/or a CABLE DISTRIBUTION SYSTEM.
Requirements additional to those specified in this European Standard may be necessary for
• equipment intended for operation while exposed, for example, to extremes of temperature, to excessive dust, moisture, or vibration, to flammable gases. to corrosive or explosive atmospheres,
• electromedical applications with physical connections to the patient.
The requirements for the following items are not covered by this European Standard:
• functional reliability of equipment:
• communication facilities with remote supply using hazardous voltage:
• protection of equipment, TELECOMMUNICATION NETWORKS and/or CABLE DISTRIBUTION SYSTEMS from damage.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
3 Definitions
For the purposes of this document, the terms and definitions of EN 60950-1 apply.
NOTE 1 Defined terms are printed In SMA CAPIFALS.
NOTE 2 For information about TE ECO4MUNKATI0N NEtWORK voltages and signals, see Annex B.
4 Safety requirements and compliance criteria
NOTE It Is assned that adequate measures according to ITU-T Recommendation K.11 have been taten to reduce the hke4ihood that the overvoltages presented to the equipment exceed 1.5 kV peak. In instalations wtiere oveivoltages presented to the equipment may exceed 1.5 kV peak, additional measures such as surge suppression may be necessary
The general conditions for tests of EN 60950-1, 1.4 apply.
The references to the requirements of EN 60950-1, 4.2.2 and 4.2.3 may be replaced by the corresponding requirements in other relevant safety standards listed in Annex A, if the equipment is designed to comply with one of these standards.
4.1 Interconnection of equipment — General requirements EN 60950-1. 3.5.1 applies.
4.1.1 Types of Interconnection circuits EN 60950-1, 3.5.2 applies.
4.1.2 ELV circuits as interconnection circuits EN 60950-1, 3.5.3 applies.
4.1.3 Safety statements
The safety status (SELV CIRCUIT, TNV-1 CIRcuIT; TNV-2 CIRCUIT; TNV-3 CIRCUIT, LIMITED GUiEN1 CIRCUIT, ELV CIRCUIT AND HAZARDOUS VOLTAGE) of interconnection points for the connection to other equipment shall be stated in the manufacturer’s documentation supplied with the equipment.
4.2 TNV circuits
4.2.1 Limits
EN 60950-1, 2.3.1 applies.
4.2.2 Separation of TNV circuits from other circuits and from accessible parts
4.3.2 Protection In service access areas For TNV CIRCUITS EN 60950-1, 2.1.2 applies.
4.3.3 Protection In restricted access location For TNV CIRCUITS EN 60950-1, 2.1.3 applies.
4.4 Protection of TELECOêWUMCAT1ON NETWORK and/or cable distribution network service
persons, and users of other equipment connected to the network, from hazards in the equipment
4.4i Protection from hazardous voltages
EN 60950-1, 6.1.1 or relevant parts of 7 respectively applies.
4.4.2 Use of protective earthing EN 60950-1, 2.6.5.8 applies.
For the protective earthing of TNV CIRCUITS EN 60950-1, 2.6.1 (items C), d). arid 1)), 2.6.3. and 2.6.4 apply.
4.4.3 Separation of the TELECOMMUNICATiON NETWORK from earth EN 60950-1, 6.1.2 or relevant parts of 7 respectively applies.
4.4.4 Touch current to TELECOMMUNICATiON NETWORKS and CABLE DISTRIBUTION SYSTEM and from TELECOMMUNICATiON NETWORKS
EN 60950-1, 5.1.8 applies.
4.4.5 SummatIon of touch currents from TELICOMMUNPCATION NETWORKS EN 60950-1, 5.1.8.2 applies.
4.5 ProtectIon of equipment users from overvoltages on TELECOMMUNICATION NETWORKS and/or
CA8LE DISTRIBUTiON SYSTEMS
EN 60950-1, 6.2.1 and 6.2.2 or relevant parts of 7 respectively apply.
4.6 Protection of the telecommunication wiring system from overheating EN 60950-1, 6.3 applies.BS EN 41003-2009 pdf download.
BS EN 41003-2009 pdf download
PS:Thank you for your support!
