BS/EN 2084-2018 pdf download.Aerospace series – Cables, electrical, general purpose, with conductors in copper or copper alloy – Technical specification.
The following documents, in whole or in part, are normatively referenced In this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
20J334 Aerospace series — Copper and copper alloys conductors for electrical cables — Product standard EN 2235. Aerospace series — Single and multicore electrical cables, screened and jacketed — Technical specification
EN 3475400. Aerospace series — Cables, electrical, aircraft use — Test methods — Part 100: General EN31Il3 Aerospace series — RequIrements and Ceses on user-applied markings on aircraft electrical cables EN 4434, Aerospace series — Copper or copper alloy lightweight conductors for electrical cables — Product
standard (Normal and tight tolerances)
EN 9102. Aerospace series — Quality systems — First article inspection requirements
EN 9133. Aerospace series — Quality Management Systems — Qualification Procedure for Aerospace Standard Products
ISO 2574. Aircraft — Electrical cables — Identification marking
3 Terms, definitions and symbols
For the purposes of this document, the terms, definitions and symbols given in EN 3475-100 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at htpJww&kct[Qpvdi1rgJ
• ISO Online browsing platform: available at http://www.iso.org/obp
4 Materials and construction of cables
4.1 Conductors
They shall be conform to EN2V3 and/or EN 4434, unless otherwise specified.
4.2 Finished cables
The insulation material shall present on uniform circular cross-section throughout the length of the cable.
Covering over the insulation shall be treated and applied in such a manner that the cables present a smooth appearance (unless the acceptable overlap due to a tape wrapped technology) and are able to accept marking.
Multiconductors assembly shall he cabled according N ZZ3S.
5 Required characteristics
The characteristics of the cables, tested according to the methods described hereafter shall comply with the values given in the product standard.
6 Tests methods
6.1 Single core cables
See Table 1.
7.1.2 QualifIcation conditions
The cables shall be submitted for qualification tests on drums, spools or in coils in sufficient lengths, wound evenly and uniformly.
Each drum, spool or coil shall have a label containing information given in 91.
7.1.3 QualifIcation tests
See Table 1.
Multicore cables they shall be manufactured with qualified single core cables. Multicore cables shall be tested in accordance with Table 2.
7.1.4 Extension of qualification
The qualification granted may be applicable to all the cross-sections in a group in accordance with Table 3 and Table 4 provided that the same construction, processes and materials are used.
The tests shall be carried out on all cables delivered. See Table I and Table 2.
7.2.3 Tests prior to delivery
They shall be carried out by sampling on each production batch prior to delivery.
See Table 1 and Table 2.
7.2.4 Periodic tests
They shall be carried out by sampling every three (3) years in accordance with Table 1 and Table 2 by sampling from cables that have been manufactured and released within the last six (6) months. Samples are to be included from each of the cable groups in Table 3 and Table 4.
See Table 1 and Table 2.
7.2.5 First article inspection tests
The first article inspection tests are to be carried out on all cable designs.
See Table 1 and Table 2.
8 Identification marking
Unless otherwise specified, the type. cross-section and a reference for identification of country of origin, manufacturer, and the year of manufacture shall be indelibly marked on the cables, in accordance with ISO 2574.
9 Packaging, labelling and delivery lengths
9.1 Packaging and labelling
Cables supplied on drum, spools or in coils shall be wound evenly and uniformly.
All cable ends shall be easily accessible and protected where necessary.
Each drum, spool or coil shall have a label indicating:
• manufacturer’s name and designation;
• cable designation according to the EN product standard;BS/EN 2084-2018 pdf download.
BS/EN 2084-2018 pdf download
PS:Thank you for your support!
