BS/EN 1519-1-2019 pdf download.Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Polyethylene (PE) Part 1: Requirements for pipes, fittings and the system.
EN ISO 472. Plastics- Vocabula,y (iSO 472)
EN ISO 580. Plastics piping and ducting systems – Injection-moulded thermo plastics fittings – Methods for visually assessing the effects of heating (ISO 580)
EN ISO 1043-1. Plastics – Symbols and abbreviated terms – Part 1: Basic polymers and their special characteristics (ISO 1043-1)
EN ISO 1133-1. Plastics – Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics – Part 1: Standard method (ISO 1133-1)
EN ISO 1167-1, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids – Determination of the resistance to internal pressure – Part 1: General method (ISO 1167-1)
EN ISO 1167-2, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids – Determination of the resistance to internal pressure – Part 2: Preparation of pipe test pieces (iSO 1167-2)
EN ISO 1183-2, Plastics – Methods for determining the density of non-cellular plastics – Part 2: Density gradient column method (iSO 1183-2)
EN ISO 2505, ThermopIastics pipes – Longitudinal reversion. Test method and parameters (ISO 2505)
EN ISO 3126, Plastics piping systems – Plastics components – Determination of dimensions (ISO 3126)
EN ISO 3451-1, Plastics – Determination of ash – Part 1: General methods (ISO 3451-1)
EN ISO 11357-6, Plastics – Differential scanning calorimetry (DSC) – Part 6: Determination of oxidation
induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) (iSO 11357-6)
EN ISO 9969, Thermopiastics pipes – Determination of ring stiffness (150 9969)
EN ISO 13254, Thermoplascics piping systems for non-pressure applications Test method for watertighiness (1SO 13254)
EN ISO 13255, Thermoplastics piping systems for soil and waste discharge inside buildings – Test method for airtightness ofjoints (ISO 13255)
EN ISO 13257:2018, Thermoplastics piping systems for non-pressure applications – Test method for resistance to elevated temperature cycling (ISO 13257:2018)
EN ISO 13259, Thermoplastics piping systems for underground non-pressure applications- Test method for leaktightness of elastomeric sealing ring type joints (ISO 13259)
EN ISO 13264, Thermoplastics piping systems for non-pressure underground drainage and sewerageThermo plastics fittings- Test method for mechanical strength or flexibility offabricated fittings (iSO 13264)
ISO 4065, Thermo plastics pipes – Universal wall thickness table
3 Terms and definitions
For the purposes 01 this document, the terms and dehnitions given in EN ISO 472, EN ISO 1043-1 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://wwwiso.org/obp
3.1
application area code
code used in the marking of pipes and fittings to indicate the permitted application area(s) for which they are intended as follows:
— B: application area code for components intended for use above ground Inside the building, or for components outside buildings fixed onto the wall;
— D: application code for the area under and within I m from the building where the pipes and fittings are buried in ground and are connected to the underground drainage and sewerage system;
— BD: application area code for components intended for use for both code B and code 0 application areas
Note ito entry: In U application areas, the existence 01 external forces from the surroundings in addition to the hot water discharge Is usual.
Note 2 to entry: Other application area codes U and UD not covered by this standard are defined elsewhere, e.g. in EN 12666-1 151.
3.2
nominal size
3.2.1
nominal size
3.6
inside diameter
value of the measurement of the inside diameter through its cross section at any point of a socket, rounded to the next greater 0,1 mm
3.7
mean inside diameter of a socket dsm
arithmetical mean of a number of measurements of the inside diameter of a socket in the same cross section
wall thickness
value of measurement of the wall thickness at any point around the circumference of a component
3.9
mean wall thickness
arithmetical mean of a number of measurements of the wall thickness, regularly spaced around the circumference and in the same cross section of a component, including the measured minimum and the measured maximum values of the wall thickness in that cross section
3.10
pipe series
dimensionless number for pipe designation
Note 1 to entry: See Iso 4065.
standard dimension ratio
SDR
nominal ratio of the outside diameter, d, to the minimum wall thickness, Cmfl
3.12
nominal ring stiffness
SN
numerical designation of the ring stiffness of a pipe or fitting which is a convenient round number relative
to the determined stiffness.BS/EN 1519-1-2019 pdf download.
BS/EN 1519-1-2019 pdf download
PS:Thank you for your support!
