BS/EN 1329-1-2020 pdf download.Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure — Unpiasticized poly(vinyl chloride) (PVC-U) Part 1: Specifications for pipes, fittings and the system.
EN ISO 1158, Plastics — Vinyl chloride homopolymers and copolymers — Determination of chlorine content (ISO 1158)
EN ISO 1167-1:2006, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 1: General method (ISO 1167-1:2006)
EN ISO 1167-2:2006, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces
(iSO 1167-2:2006)
EN ISO 1183-1, Plastics — Methods for determining the density of non-cellular plastics — Part 1:
Immersion method, liquid pycnometer method and titration method (ISO 1183-1)
EN ISO 2505, Thermoplastics pipes — Longitudinal reversion — Test method and parameters (ISO 2505) EN ISO 2507-1, Thermoplastics pipes and fittings — Vicat softening temperature — Part 1: General test
method (ISO 2507-1)
EN ISO 3126, Plastics piping systems — Plastics components — Determination of dimensions (ISO 3126)
EN ISO 3127, Thermoplastics pipes — Determination of resistance to external blows — Round-the-clock method (ISO 3127)
EN ISO 3451-5, Plastics — Determination of ash — PartS: Poly(vinyl chloride) (ISO 3451-5)
EN ISO 6259-1, Thermoplastics pipes — Determination of tensile properties — Part 1: General test method (ISO 6259-1)
EN ISO 9852, Un plasticized poly(vinyl chloride) (PVC-U) pipes — Dichioromethane resistance at specified temperature (DCMT) — Test method (ISO 9852)
EN ISO 11173, The rmo plastics pipes — Determination of resistance to external blows — Staircase method
(ISO 11173)
EN ISO 13254, Thermoplastfcs piping systems for non-pressure applications — Test method for watertightness (ISO 13254)
EN ISO 13255, Thermoplastics piping systems for soil and waste discharge inside buildings — Test method for airtightness ofjoints (ISO 13255)
EN ISO 13257:20 18, Thermoplastics piping systems for non-pressure applications — Test method for resistance to elevated temperature cycling (ISO 1 3257:2018)
EN ISO 13259, Thermoplastics piping systems for underground non-pressure applications — Test method for leaktightness of elastomeric sealing ring type joints (ISO 13259)
ISO 6259-2, Thermo plastics pipes — Determination of tensile properties — Part 2: Pipes made of unpiasticized poly(vinyl chloride) (PVC-U), oriented unpiasticized poly(vinyl chloride) (PVC-O), chlorinated poly (vinyl chloride) (PVC-C) and high-impact poly (vinyl chloride) (PVC-HI)
ISO 18373-1, Rigid PVC pipes — Differential scanning calorimetry (DSC) method — Part 1: Measurement of the processing temperature
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN ISO 472 and EN ISO 1043-1 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http:/Jwww.electropedia.orgJ
— ISO Online browsing platform: available at https://www.iso,org/obp
31
application area code
code used in the marking of pipes and fittings to indicate the application area(s) for which they are intended, as follows:
— 8: application area code for components intended for use above ground inside the building, or for components outside buildings fixed onto the wall;
— D: application code for the area under and within 1 m from the building where the pipes and fittings are buried in ground and are connected to the underground drainage and sewerage system
Note ito entry: In D application areas the existence of external forces from the surroundings in addition to the hot water discharge is usual.
Note 2 to entry: Components intended for use for both code B and code D application areas are marked RD.
Note 3 to entry: Other application area codes Ii and liD not covered by this standard are defined elsewhere, e.g. in EN 1401-1.
3.6
mean outside diameter drm
value of the measurement of the outer circumference of a pipe or spigot of a fitting in any cross section, divided by it 3,142), rounded to the next greater 0,1 mm
3.7
inside diameter
value of the measurement of the inside diameter through its cross section at any point of a socket, rounded to the next greater 0,1 mm
3.8
mean Inside diameter of socket
d
arithmetical mean ol a number of measurements otr the inside diameter ot a socket in the same cross
section
3.9
out-of-roundness
ovality
difference between the measured maximum and the measured minimum outside diameter in the same cross section of a component
3.10
wall thickness
value of measurement of the wall thickness at any point around the circumference of a component
3.11
mean wall thickness em
arithmetical mean of a number of measurements of the wall thickness, regularly spaced around the circumference and in the same cross section of a component, including the measured minimum and the measured maximum values of the wall thickness in that cross section
3.12
standard dimension ratio
SDR
numerical designation of a pipe series, which is a convenient round number, approximately equal to the ratio of the nominal outside diameter of a pipe to its nominal wall thickness.BS/EN 1329-1-2020 pdf download.
BS/EN 1329-1-2020 pdf download
PS:Thank you for your support!
