ASME B73.3:2003 pdf download

12-16-2022 comment

ASME B73.3:2003 pdf download Specification for Sealless Horizontal End Suction Metallic Centrifugal Pumps for Chemical Process
1 SCOPE
This Standard covers sealless centrifugal pumps ofhorizontal end suction single stage and centerline discharge design. This Standard includes dimensionalinterchangeability requirements and certain design features to facilitate installation and maintenance. It is theintent of this Standard that pumps of the same standarddimensional designation from all sources of supply shallbe interchangeable with respect to mounting dimensions, size, and location of suction and discharge noz-zles, input shafts, baseplates, and foundation bolt holes(see Tables 1, 2, 3, and 4)
2 ALTERNATIVE DESIGN2.1 Extended Design
Dimensions for an extended length design alternativeare included. The extended length alternative shall conform to the basic design features of this Standard including those providing interchangeability with respect tomounting dimensions at the casing, size, and locationof the suction and discharge nozzles (see column headswith e suffix in Tables 1 through 4 for dimensional limits).Manufacturers, when offering extended length pumpsshall state this fact in their proposal.NOTE: For Tables 1 and 2 the extended leneth dimension is amaximum valueAny dimension between the standard and maximum extended length is acceptable.
2.2 Alternative DesignAlternative designs will be considered, provided theymeet the intent of this Standard and cover constructionand performance which are equivalent to and otherwisein accordance with this Standard. All deviations fromthese specifications shall be described in detail by theseller and approved by the purchaser.
3 NOMENCLATURE AND DEFINITIONS
All nomenclature and definitions of pump components shall be in accordance with ANSI/HI 5.1through 5.6.
canned motor pump(CMP): a type of sealless pump whichhas a common shaft to link the pump and motor in a single sealed unit. The pumped liquid is circulatedthrough the motor, but is isolated from the motor components by a corrosion-resistant containment liner.
magnetic drive pump (MDP): a type of sealless pumpwhich utilizes an outer ring of permanent magnets orelectromagnets to drive an internal rotating assemblyconsisting of an impeller, shaft, and inner drive member(torque ring or inner magnet ring) through a corrosion-resistant containment shell.
4 DESIGN AND CONSTRUCTION FEATURES4.1 Pressure and Temperature Limits
4.1.1 Pressure Limits. The design pressure of thepump shall be at least as great as the pressure-tempera-ture rating of ASME B16.5 Or ASME B1642 Class 150flanges of the material used.Primary pressure-con-taining boundary (and secondary pressure-containingboundary if required) shall be designed to withstand ahydrostatic test at 1.5 times the maximum design pres-sure for the material of construction used (see para.5,2.1)
All primary pressure-containing parts shall also becapable of resisting a vacuum of 14.7 psi (760 mmHG)at 68F(20°C).
4.1.2 Temperature Limits. Pumps should be availablefor temperatures up to 500°F(260C).Jacketing andother modifications may be required to meet theoperating temperature.
4.1.3 Statement. Temperature limitations of the liquid at the suction flange shall be stated by the pumpmanufacturer.
NOTE: The application of the pump shall take into considerationthe fluid characteristics as supplied by the user, This will requireconsideration of such characteristics as specific heat and vaporpressure of the liquid which establishes these limits
4.2 Flanges
Suction and discharge nozzles shall be flangedFlanges shall conform to ASME B165 Or ASME B1642Class 150 standards except that marking requirementsare not applicable and the maximum acceptable toler.ance on parallelism of the back of the flange shall be 3deg, and bolt holes may be tapped where noted in Tables1 and 3.

                                           Related Information                                             Download
PS:Thank you for your support!
ASME B107.100:2002 pdf download ASME Standards

ASME B107.100:2002 pdf download

ASME B107.100:2002 pdf download WKENGHLD INCORPORATING ASME B107.6, ASME B107.9, ASME B107.39, and ASME B107.40 4.5 Proof Torque When tested as specified, wrenches shall withstand the proof torque specified in the applicable tables without failure or permanent...
Read More
ASME BPE:2002 pdf download ASME Standards

ASME BPE:2002 pdf download

ASME BPE:2002 pdf download BIOPROCESSING EOUIPMENT GR-1 INTRODUCTION This Standard provides the requirements applicableto the design of bioprocessing equipment inciudingaspects related to sterilily and cleanability,dimensionsand tolcranccs, surfacc finish, material joining, andscals. Thcsc apply to: (a) componcnts that...
Read More
ASME N509:2002 pdf download ASME Standards

ASME N509:2002 pdf download

ASME N509:2002 pdf download NUCLEAR POWER PLANT UNITS AID CDMPONENTS 1 SCOPE This Standard covers requirements for the designconstruction, and qualification and acceptance testingof the air-cleaning units and components which makeup Engineered Safety Feature (ESF) and other...
Read More

LEAVE A REPLY

Anonymous netizen Fill in information