ASME B107.8:2003 pdf download

12-16-2022 comment

ASME B107.8:2003 pdf download ADJUSTABLE WRENCHES
DEFINITIONS
See Fig. 1 as applicable.
adjustab/e jaw: movable portion of the wrench that con-tacts the fastener.adjusting worm. portion of the wrench used to adjust theclearance between the fixed and adjustable jaw.
fixed jaw portion of the frame that contacts the fastenerframe portion of the wrench containing the fixed jawand handle.
hand/e. portion of the wrench by which the tool is held.proof torgue. predetermined test torque to which a sampleis subjected.
worm pin pin used to retain the adjusting worm in theframe.
worm spring: spring used to induce friction between theframe and adjusting worm for holding the adjustingworm in any preset position.
5 REQUIREMENTS
The fiqures in this Standard are descriptive and notrestrictive, and are not intended to preclude the manu:facture of wrenches that are otherwise in accordancewith this Standard.
51 Materials
The materials used in the manufacture of the
wrenches shall be such as to produce tools conformingto this Standard. The frame, adjustable jaw, adjustingworm, and worm pin shall be steel.
5.2 Marking
Wrenches shall be marked in a leqible and permanentmanner with the manufacturer’s name or with a trade-mark of such known character that the source of manu-facture and country of origin may be readily determined.
5.3 Hardness
The frame (fixed jaw and handle) and adjustable jawshall show a hardness of not less than 40 HRC nor morethan 50 HRC when tested as specified in para. 6.1.
5.4 Proof Torque
Wrenches shall withstand the proof torque specifiedherein for the appropriate size without failure or permanent deformation (set) that might affect the durability or serviceability of the wrench. There shall be no formation of cracks or fracture of any part of the wrench.including jaw, frame, worm, and worm pin. After prooftorque tests, there shall be no resultant binding or loos-ening of the adjustable jaw. Before and after the prooftorque test each wrench shall be opened and closed toverify the wrench operates over the full range of thejaw opening.
5.5 Finish
5.5.1 Surface Finish. Wrenches shall be free from rustfins, burrs, pits, nodules, and other conditions that mayimpair their serviceability, durability, safety, or appearance. The external forge flash shall be removed to blendsmoothly with adjacent surfaces.
5.5.2 Coatings. The frame and the adjustable jawshall have one or more of the coatings described below,with the exception of zinc. Worm and worm pin shallhave any of the following coatings:
(a) Nicke/-Chromium P/ate. On wrenches with decora-tive nickel-chromium plating, the minimum thicknessshall be 0.00015 in, for nickel and 0.000003 in. for chromeunless the wrench passes the test in para. 6.5 Nickeliron undercoating (16% iron max.) may be substitutedfor nickel.
(b) Phosphate. Wrenches having a chemically produced phosphate coating also shall have a coating ofrust preventive.
(c) Oxide. Wrenches having a coating consisting of achemically produced oxide also shall have a coating ofrust preventive.
(d) Zinc Adjusting worms and worm pins may havea coating of electrodeposited zinc of 0.0003 in minimumthickness.
(e)A/ternate Coatings Alternate coatings may be usecin lieu of nickel-chromium and shall be subjected to theAlternate Coating Test, as specified in para. 6.5.

                                           Related Information                                             Download
PS:Thank you for your support!
ASME B107.100:2002 pdf download ASME Standards

ASME B107.100:2002 pdf download

ASME B107.100:2002 pdf download WKENGHLD INCORPORATING ASME B107.6, ASME B107.9, ASME B107.39, and ASME B107.40 4.5 Proof Torque When tested as specified, wrenches shall withstand the proof torque specified in the applicable tables without failure or permanent...
Read More
ASME BPE:2002 pdf download ASME Standards

ASME BPE:2002 pdf download

ASME BPE:2002 pdf download BIOPROCESSING EOUIPMENT GR-1 INTRODUCTION This Standard provides the requirements applicableto the design of bioprocessing equipment inciudingaspects related to sterilily and cleanability,dimensionsand tolcranccs, surfacc finish, material joining, andscals. Thcsc apply to: (a) componcnts that...
Read More
ASME N509:2002 pdf download ASME Standards

ASME N509:2002 pdf download

ASME N509:2002 pdf download NUCLEAR POWER PLANT UNITS AID CDMPONENTS 1 SCOPE This Standard covers requirements for the designconstruction, and qualification and acceptance testingof the air-cleaning units and components which makeup Engineered Safety Feature (ESF) and other...
Read More

LEAVE A REPLY

Anonymous netizen Fill in information