AIA/NAS 1399-2012 pdf download RIVET, BLIND, 1 00° FLUSH HEAD, LOCKED SPINDLE
CODE:
“B”AFTER BASIC PART NUMBER INDICATES 5056 ALUMINUM ALLOY SLEEVE”D”AFTER BASIC PART NUMBER INDICATES 2017 ALUMINUM ALLOY SLEEVE”M”AFTER BASIC PART NUMBER INDICATES NICKEL-COPPER SLEEVE”CAFTER BASIC PART NUMBER INDICATES A286 CRES SLEEVE”FC” AFTER MATERIAL CODE LETTERS B” OR D”IDICATES CHEMICAL FILM FINISH ON SLEEVE AND
SPINDLE
“P” AFTER MATERIAL CODE LETTERS B” OR DINDICATES ANODIZE FINISH ON SLEEVE AND SPINDLE”W”AFTER MATERIAL CODE LETTERS M”OR C”INDICATES CADMIUM-PLATED SLEEVE”S”AFTER MATERIAL CODE LETTERS “M”OR”C”INDICATES SILVER-PLATED SLEEVE”FA”AFTER MATERIAL CODE LETTER “C”INDICATES DRY FILM LUBED SLEEVEA”IN PLACE OF “_” BETWEEN DIAMETER AND GRIP INDICAES RIVET WITH FULL SERRATED SPINDLEAB”IN PLACE OF “_” ETWEEN DIAMETER AND GRIP INDICATES RIVET WITH FULL SERRATED SPINDLE& DRIVING ANVIL
EXAMPLES OF PART NUMBER:
NAS1399M4-4NICKEL-COPPER-ALLOY RIVETO125 WITH 188 TO 250 GRIP RANGE,NO FINISHON SLEEVE,WITH PARTIAL SERRATED SPINDLE AND INDENTED DOT OR CONEIDENTIFICATION5056 ALUMINUM ALLOY RIVET,D.125 WITH 188 TO 250 GRIP RANGE,WITHPARTIAL SERRATED SPINDLE AND INDENTED DOT OR CONE IDENTIFICATIONFINISH OPTIONAL – CHEMICAL FILM OR ANODIZE,ORANGE COLORED SLEEVENAS1399MW4A4=NICKEL-COPPER-ALLOY RIVET,O125 WITH 188 TO 250 GRIP RANGE,CADMIUM-PLATED，WITH FULL SERRATED SPINDLE AND INDENTED CIRCLE IDENTIFICATION
NA51399B4-4
NA51399D4AB42017 ALUMINUM-ALLOY RIVET,O125 WITH.188 TO 250 GRIP RANGEWITHDRIVING ANVIL，FULL SERRATED SPINDLE AND INDENTED CIRCLEIDENTIFICATION，FINISH OPTIONAL – CHEMICAL FILM OR ANODIZENAS1399BFC4-45056 ALUMINUM ALLOY RIVET,O.125 WITH 188 TO 250 GRIP RANGE,WITHPARTIAL SERRATED SPINDLE AND INDENTED DOT OR CONE IDENTIFICATIONFINISH -CHEMICAL FILM
001 SHANK DIA INCREASE PERMISSIBLE WITHIN10 INCH BASE OF HEAD
MAXIMUM HEAD DIAMETERS ARE THEOREICAL SHARP CORNERS AS MEASURED BY PROJECTION.
AVAILABLE IN”C”MATERIAL CODE TYPE”A”AND NO CODE”ONLY.
THE MATERIAL AND FINISH LISTED ARE FOR RIVETS WITH PARTIAL SERRATED SPINDLES ONLY. FORTHE FULLY SERRATED SPINDLE SERIES THE LOCK RING MAY BE INTREGAL WITH THE SLEEVE IN WHICHCASE THE LOCK RING IS OF THE SAME MATERIAL AND FINISH AS THE SLEEVE
INTERCHANGEABILITY: THE A” AND AB” CODE RIVETS (FULL SERRATIONS) AND NO CODE RIVETS(PARTIAL SERRATIONS) ARE PHYSICALLY AND FUNCTIONALLY INTERCHANGEABLE EXCEPT FORINSTALLATION TOOLS(PULLING HEADS)
CAUTION: RIVETS WITH DIFFERENT SPINDLE CONFIGURATIONS CANNOT BE INSTALLED WITH THESAME TOOL (PULLING HEAD); SEE PARAGRAPH 6.3 OF NAS1400
DIMENSIONS IN INCHES AND APPLY AFTER FINISH AND PRIOR TO THE APPLICATION OF LUBRICATIONUNLESS OTHERWISE SPECIFIED
THIS STANDARD TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.
UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THEAPPLICABLE DRAWING OR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED
UNLESS OTHERWISE SPECIFIED HEREIN, REFERENCED DOCUMENTS SHALL BE THE ISSUE IN EFFECT ONDATE OF MANUFACTURE. HOWEVEREXISTING MATERIAL INVENTORY CERTIFIED TO A PREVIOUSREVISION OF THE APPLICABLE MATERIAL SPECIFICATION(S) IS ACCEPTABLE FOR USE UNTILDEPLETION.
DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982.
AIA/NAS 1399-2012 pdf download
PS:Thank you for your support!
