AIA/NAS 1398-2012 pdf download RIVET, BLIND, PROTRUDING HEAD, LOCKED SPINDLE
CODE:
“B”AFTER BASIC PART NUMBER INDICATES 5056 ALUMINUM ALLOY SLEEVE”D”AFTER BASIC PART NUMBER INDICATES 2017 ALUMINUM ALLOY SLEEVE“M”AFTER BASIC PART NUMBER INDICATES NICKEL-COPPER SLEEVE”C”AFTER BASIC PART NUMBER INDICATES A286 CRES SLEEVE”FC” AFTER MATERIAL CODE LETTERS B” OR D”INDICATES CHEMICAL FILM FINISH ON SLEEVE &SPINDLE”P” AFTER MATERIAL CODE LETTERS “B” OR D”INDICATES ANODIZE FINISH ON SLEEVE & SPINDLE”W”AFTER MATERIAL CODE LETTERS M”OR C”INDICATES CADMIUM-PLATED SLEEVE”S”AFTER MATERIAL CODE LETTERS M”OR C”NDICATES SILVER-PLATED SLEEVE”FA”AFTER MATERIAL CODE LETTER C”INDICATES DRY FILM LUBRICATED SLEEVE”A”IN PLACE OF “_” BETWEEN DIAMETER AND GRIP INDICATES RIVET WITH FULL SERRATED SPINDLE”ABIN PLACE OF “-” BETWEEN DIAMETER AND GRIP INDICATES RIVET WITH FULL SERRATED SPINDLE
& DRIVING ANVIL
EXAMPLES OF PART NUMBER:
NICKEL-COPPER-ALLOY RIVET,O125 WITH 188 TO .250 GRIP RANGE,NO FINISHNAS1398M4-4ON SLEEVE,WITH PARTIAL SERRATED SPINDLE AND INDENTED DOT OR CONEIDENTIFICATION5056 ALUMINUM ALLOY RIVET,O.125 WITH 188 TO .250 GRIP RANGEWITHPARTIAL SERRATED SPINDLE AND INDENTED DOT OR CONE IDENTIFICATIONFINISH OPTIONAL – CHEMICAL FILM OR ANODIZEORANGE COLORED SLEEVENAS1398MW4A4NICKEL-COPPER-ALLOY RIVET,O.125 WITH .88 TO 250 GRIP RANGECADMIUM-PLATEDWITH FULL SERRATED SPINDLE AND INDENTED CIRCLE IDENTIFICATION
NAS1398B4-4
NOTES:
NAS1398D4AB4 =2017 ALUMINUM-ALLOY RIVET,D.125 WITH 188 TO 250 GRIP RANGE,WITHDRIVING ANVIL，FULL SERRATED SPINDLE AND INDENTED CIRCLEIDENTIFICATIONFINISH OPTIONAL – CHEMICAL FILM OR ANODIZENAS1398BFC4-415056 ALUMINUM ALLOY RIVET.O.125 WITH 188 TO 250 GRIP RANGEWITHPARTIAL SERRATED SPINDLE AND INDENTED DOT OR CONE IDENTIFICATIONFINISH – CHEMICAL FILM
001 SHANK DIA INCREASE PERMISSIBLE WITHIN 100 INCH OF BASE OF HEAD
AVAILABLE IN “C”MATERIAL CODE TYPE “A” AND NO CODE” ONLY.
THE MATERIAL AND FINISH LISTED ARE FOR RIVETS WITH PARTIAL SERRATED SPINDLES ONLY. FORTHE FULLY SERRATED SPINDLE SERIES, THE LOCK RING MAY BE INTREGAL WITH THE SLEEVE INWHICH CASE THE LOCK RING IS OF THE SAME MATERIAL AND FINISH AS THE SLEEVE.
INTERCHANGEABILITY: THE A” AND AB CODE RIVETS (FULL SERRATIONS) AND NO CODE RIVETS(PARTIAL SERRATIONS) ARE PHYSICALLY AND FUNCTIONALLY INTERCHANGEABLE EXCEPT FORINSTALLATION TOOLS (PULLING HEADS)
CAUTION: RIVETS WITH DIFFERENT SPINDLE CONFIGURATIONS CANNOT BE INSTALLED WITH THESAME TOOL (PULLING HEAD): SEE PARAGRAPH 6.3 OF NAS1400
DIMENSIONS IN INCHES AND APPLY AFTER FINISH AND PRIOR TO THE APPLICATION OF LUBRICATIONUNLESS OTHERWISE SPECIFIED.
THIS STANDARD TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.
UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THEAPPLICABLE DRAWING OR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED
UNLESS OTHERWISE SPECIFIED HEREIN,REFERENCED DOCUMENTS SHALL BE THE ISSUE IN EFFECT ONDATE OF MANUFACTURE HOWEVER,EXISTING MATERIAL INVENTORY CERTIFIED TO A PREVIOUSREVISION OF THE APPLICABLE MATERIAL SPECIFICATIO(S) IS ACCEPTABLE FOR USE UNTIL
DEPLETION
DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982
AIA/NAS 1398-2012 pdf download
PS:Thank you for your support!
