ASME B5.49:1998 pdf download

12-15-2022 comment

ASME B5.49:1998 pdf download GLOSSARY 0F POWER PRESS TERMS
1 SCOPE AND PURPOSE
1.1 Scope
This Stundard provides 4 glossary of terms commonlyused in the industries that manufacture or use mechanically and hydraulically powcred prcsscs.
NOTE: Often two or more terms are used for the same definitionIn this Standard,only the preferred tertn is defined. Synonymousterms are listed, with a reference to the preferred term instead ofrcpctition of its definition.
() Exampe:
air pin preferred term is presgure pin.
Related terms are provided where applicable, foilowing the definitionof the tenm provided.
(2) Fxample:
Reference; hom press
1.2 Purpose
The purpose of this Standard is to define the termsmost commonly used in the industries that manufactureor use mechanically and hydraulically powered pressesto facilitate communication and understanding
2 DEFINITIONS
actuafing confrol: an operator control used to initiateslide motion.
adapfer plate: a plate or Tabricatlon instafled berweenthe die(s) and the slide. to accommodate the die configuration to the slide face for proper location and fastening
ADC: automaric die change.
adjusrable barrier guard: a guard with provisions foradjustment to accommodate various jobs or toolingsctups.
adjustable bed: a bed bolted to the straight, verticalfinished surface of a hom or gap press frame andsupported, and adjusted up and down, by means of ascrew or screws usually operated by a hand mechanism.
adjustable bed press: a gap frame press with a straightfront that is equipped with, or arranged for, an adjust-able bed.
adjustable stroke: the capability of yarying the lengthof stroke of a slide.
adjustment of a slide: preferred term is slide adjusiment.
air cushion: preferred term is die cuxhion
preferred term is die cushion.air jack:
preferred term is die cushion.air pad:
air pin:prefcrred term is pressure pin.
air press:preferred term is pneumatic power press.
antirepear: the function of the control system thatlimits the press to a single cycle with the actuatingcontrol(s) held operated
with a two-hand control device, theanti tiedown:function of the control system that requires the releaseof al] actuators before press operation can be reinitiatedautomalic die chage: the fully programmable procedure for changing from the current die sctup to asocond dic setup, without any manual intervention.automalic die clamp: a power actuated means forfastening dies into the press.
automalic feeding: the process whereby means otherthan manual are used to place the material or workpiece(s) into the press and to remove the material orworkpiece(s) from the press.
automatic mode: any operating mode that producescontinuous cycling
Can also refer to the bed (of a large straight sidepress) mounted and guided in the press frame andprovided with a suitable mechanism, usually operatedby power, for varying the press shutheightAn exampleis a wedge adjustment on a knuckle joint press.

                                           Related Information                                             Download
PS:Thank you for your support!
ASME B107.100:2002 pdf download ASME Standards

ASME B107.100:2002 pdf download

ASME B107.100:2002 pdf download WKENGHLD INCORPORATING ASME B107.6, ASME B107.9, ASME B107.39, and ASME B107.40 4.5 Proof Torque When tested as specified, wrenches shall withstand the proof torque specified in the applicable tables without failure or permanent...
Read More
ASME BPE:2002 pdf download ASME Standards

ASME BPE:2002 pdf download

ASME BPE:2002 pdf download BIOPROCESSING EOUIPMENT GR-1 INTRODUCTION This Standard provides the requirements applicableto the design of bioprocessing equipment inciudingaspects related to sterilily and cleanability,dimensionsand tolcranccs, surfacc finish, material joining, andscals. Thcsc apply to: (a) componcnts that...
Read More
ASME N509:2002 pdf download ASME Standards

ASME N509:2002 pdf download

ASME N509:2002 pdf download NUCLEAR POWER PLANT UNITS AID CDMPONENTS 1 SCOPE This Standard covers requirements for the designconstruction, and qualification and acceptance testingof the air-cleaning units and components which makeup Engineered Safety Feature (ESF) and other...
Read More

LEAVE A REPLY

Anonymous netizen Fill in information