EN 510-2019 pdf download.Specification for protective clothing for use where there is a risk of entanglement with moving parts.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
EN ISO 13688:2013, Protective clothing – General requirements (ISO 13688:2013)
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— I EC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at littpwww.iso.grgJobp
4 Requirements
4.1 General
The requirements of EN ISO 13688:2013 regarding innocuousness (4.2), comfort (4.4), ageing (5) apply.
The design requirements in 4.2 shall be checked by visual and manual inspection of the garment and If required, by testing certain elements of the garment.
4.2 Design
4.2.1 Basic design requirements
4.2.1.1 General
The design requirements are complementary to subclause 4.3 of EN ISO 13688:2013. The design of the garment shall comply with the following principles:
a) a covering of any other garment
b) acloseflt
c) a smooth outer surface of the garment.
4.2.1.2 Fastening requirements
The garment shall be fastened by means having no exposed loose ends. The fastening elements shall be concealed. Folds caused by fastening elements shall lie on the inner side of the garment.
After cleaning in accordance to 5.2 of EN ISO 13688:2013, the functionality of the fastening elements shall be checked by closing and opening manually the fastening elements five times.
4.2.1.3 Cuff and trouser lower-hem requirements
Cuffs shall not have turn-ups.
Lower hems of trousers or one-piece suits shall not have turn-ups.
4.2.1.4 Pocket requirements
There shall be no external pockets.
Any inside pocket of the garment above the waist shall not be provided with pocket openings on the outside and shall only be accessible from inside the garment.
Any inside pocket of the garment below the waist with pocket openings on the outside shall be closable.
4.2.2 Additional design requirements in relation to the garment type
4.2.2.1 General
The garment or garment ensemble shall consist of:
a) waist jacket (see 4.2.2.2) with bib and brace overall (see 4.2.2.3) or
b) waist jacket (see 4.2.2.2) with sleeveless coverall (see 4.2.2.4) or
c) coverall with sleeves (see 4.2.2.4).
Examples of possible designs are shown in Figure 1.
4.2.2.2 WaIst jacket
The waist jacket shall either have a stand-up collar or be collarless. The jacket shall be closable up to the collar or neck band.
The back and the front shall have no formed folds. The cuff shall be adjustable to give a close fit.
The bottom of the waist jacket shall be adjustable to achieve close fitting.
4.2.2.3 Bib and brace overall
If a side opening is required it shall be closable along the whole length of the side opening (e.g. touch- and-close fastener).
The brace shall be sewn on the back and the effective length of the brace shall be adjustable. The buckles required for adjustment shall be sewn on the bib; they shall be so designed that the ends of the braces hang on the inner side of the bib. The braces shall be of extensible material.
The width of the waist shall be adjustable by internal means.
The trouser bottoms shall be adjustable to give a close fit.
4.2.2.4 Coverall with or without sleeves
The features as specified in 4.2.2.2 and 4.2.2.3 shall equally apply to coveralls. The width of the waist shall be adjustable by internal means. Sleeveless coveralls shall have an extensible back.
5 Dimensional change
The dimensional change due to cleaning shall comply with the requirements of 5.3 of
EN ISO 13688:2013, when tested according to 5.3 of EN ISO 13688:2013.
6 General size designation
The general size designation shall comply with Clause 6 of EN ISO 13688:2013.
7 Marking
The marking shall comply with Clause 7 of EN ISO 13688:2013.
The marking shall use the graphical symbol in Figure 2 intended for protection against moving parts (see ISO 7000-2411).EN 510-2019 pdf download.
EN 510-2019 pdf download
PS:Thank you for your support!
