PAS 62050:2004 pdf download

12-31-2022 comment

DD IEC PAS 62050:2004 pdf download Board level drop test method of components for handheld electronic products
The Board Level Drop Test Method is intended to evaluate and compare drop performance of surfacemount electronic components for handheld electronic product applications in an accelerated testenvironment, where excessive flexure of a circuit board causes product failure. The purpose is tostandardize the test board and test methodology to provide a reproducible assessment of the drop testperformance of surface mounted components while duplicating the failure modes normally observedduring product level test.
The purpose of this document is to prescribe a standardized test method and reporting procedure. This isnot a component qualification test and is not mcant to replace any system level drop test that maybeneeded to qualify a specific handheld electronic product. The standard is not meant to cover the drop testrequired to simulate shipping and handling related shock of electronic components or PCB assemblics.These requirements are already addressed in JESD22-B104-B and JESD22-B110. The method isapplicable to both area-array and perimeter-leaded surface mounted packages.
Correlation between test and field conditions is not yet fully established. Consequently, the testprocedure is presently more appropriate for relative component performance than for use as a pass/failcriterion, Rather, results should be used to augment existing data or establish baseline for potentialinvestigative efforts in package/board technologies.
The comparability between different test sites, data acquisition methods, and board manufacturers hasnot been fully demonstrated by existing data. As a result, if the data are to be used for direct comparisonof component performance, matching study must first be performed to prove that the data are in factcomparable across different test sites and test conditions.
This method is not intended to substitute for full characterization testing. which might incorporatesubstantially larger sample sizes and increased number of drops. Due to limited sample size and numberof drops specified here, t is possible that enough failure data may not be generated in every case toperform full statistical analysis.
2Apparatus
As perJESD22-B104-B and JESDD22-B110
Terms and definitions
For purposes of this standard, the following definitions shall apply
component: A packaged semiconductor device.
single-sided PCB assembly: A printed circuit board assembly with components mounted on only oneside of the board
double-sided PCB assembly: A printed circuit board assembly with components mounted on top andbottom sides of the board.
handheld electronic product: A product that can conveniently be stored in a pocket (of sufficient size)and used when held in user’s hand.
NOTE Included in handheld electronic products are cameras, calculators, cell phones, pagers, palm-size PCsformerly called “pocket organizers). Personal Computer Memory Card International Association (PCMCIA) cardssmart cards, mmobile phones, personal digital assistants (PDAs), and other communication devices.
peak acceleration: The maximum acceleration during the dynamic motion of the test apparatus.
pulse duration; acceleration interval: The time interval between the instant when the acceleration firstreaches 10% of its specified peak level and the instant when the acceleration first returns to 10% of thespecified peak level after having reach that peak level.
table drop height: The free-fall drop height of the drop table needed to attain the prescribed peakacceleration and pulse duration.
event: An electrical discontinuity of resistance greater than 1000 ohms lasting for 1 microsecond orlonger.
event detector: A continuity test instrument capable of detecting electrical discontinuity of resistancegreater than 1000 ohms lasting for 1 microsecond or longer.
4Applicable documents
JESD22-B104-B,Mechanical Shock
IESD22-B110.Subassemblv Mechanical Shock
IPC-SMT-782, Surface Mount Design and Land Pattern Standard
IPC-A-600.Acceptability of Printed Boards
J-STD-020, Moisture/Reflow Sensitivity Classification for Non-hermetic Solid State Surface Mount
Devices

                                           Related Information                                             Download
PS:Thank you for your support!
IEC PAS 61162-103:2006 pdf download PAS Standards

IEC PAS 61162-103:2006 pdf download

IEC PAS 61162-103:2006 pdf download Maritime navigation and radiocommunication equipment and systems – Digital interfaces – Part 103: Single talker and multiple listeners – New and amended sentences and Talker IDs 1 Scope IEC 61162-1:2016 supports the...
Read More
BS PD IEC PAS 61162-101:2003 pdf download PAS Standards

BS PD IEC PAS 61162-101:2003 pdf download

BS PD IEC PAS 61162-101:2003 pdf download Maritime navigation and radiocommunication equipment and systems – Digital interfaces – Part 101: Single talker and multiple listeners – Modified sentences and requirements for IEC 61162-1 Scope This PAS document...
Read More
PAS 61162-102:2003 pdf download PAS Standards

PAS 61162-102:2003 pdf download

PAS 61162-102:2003 pdf download Maritime navigation and radiocommunication equipment and systems – Digital interfaces – Part 102: Single talker and multiple listeners – Extra requirements to IEC 61162-1 for the Voyage Data Recorder Scope The lEC 61162-1...
Read More

LEAVE A REPLY

Anonymous netizen Fill in information